Waterborne Silicone-Acrylic Emulsion Paint- Multicolor

Waterborne Silicone-Acrylic Emulsion Paint- Multicolor

Product Description:

- Model:725-WQF-2

- A single pack waterborne paint.

Intended Uses:

- For use as flame retardant and decoration at the surface of steel, wood, insulation fabric and cable.

- For livingroom of ship

Product Information:

Volume Solids:42%±2%                  Finish/Sheen:  Matt

Film Thickness(μm)

Min

Typical

Max

Dryfilm Thickness

40

40

80

Wetfilm Thickness

95

95

190

Theoretical Coverage(m2/L)

10.5

10.5

5.2

Mix Ratio: One pack

Method of Application

 

Airless Spray

Recommended

Tip size range:0.38-0.53mm

Output pressure:15MPa

Air Spray

Tip size range:2.0-3.0mm

Output pressure:0.4MPa

Brush/Roller

Need to coat several times to get film  thickness.

Thinner

Not recommended. Use only in exceptional circumstances (volume 5%).

Cleaner

Water

Induction Period

Not necessary

Drying Information:

 

5℃

15℃

25℃

Touch Dry

4h

3h

2h

Hard Dry

48h

36h

24h

Pot Life

Not applicable

Overcoating Data:

 

5℃

   15℃

  25℃

Overcoated by

Min Max

Min Max

Min Max

725-WQF-2

   48h

   36h

   24h

Storage:

Store in cool and dry conditions,Well ventilate.Keep away from hot and fire. Shelf Life: 12 months

minimum at 25 ℃,Subject to re-inspection thereafter.

Pack Size: 25kg/18L in 20L container

Systems and Compatibility:

Consult your Sunrui Representative for the systems best suited for the surfaces to be protected.

Surface Preparation:

High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning. All surfaces to be coated should be clean, dry and free from contamination.

Newbuilding/Major Refurbishment:

725-WQF-2 should be applied over a recommended primer coating scheme. The primer surface should be clean, dry and free from contamination.725- WQF-2 must be applied within the coating interval specified (consult the relevant product data sheet). Areas of breakdown, damage etc. should be prepared to the specified standard (eg. St3) and primed prior to the application of 725-WQF-2. 

Repair/On Board Maintenance:

1)725-WQF-2 should be applied over a recommended primer coating scheme. The primer surface should be clean, dry and free from contamination. 725- WQF-2 must be applied within the coating interval specified (consult the relevant product data sheet). Areas of breakdown, damage etc. should be prepared to the specified standard (eg. St3) and primed prior to the application of 725-WQF-2.

2)725-WQF-2 may be applied directly over aged 725-WQF-2 following thorough fresh water washing and degreasing provided the coating to be overcoated is in an intact and tightly adherent condition. Loose or flaking coatings should be removed back to a firm edge and 725-WQF-2 or an appropriate primer should be used to repair the area before application of the full coat.

Limitation:

1)Apply 725-WQF-2 when the temperature is more than 0℃ and the humidity is lower than 85%.

2)It must be ventilate above 8h at pool ventilation area.

3)The dry time and overcoating interval may change according to the environment factors.

4)Forbid to trample or pollute the surface of 725-WQF-2 and coat the next paint before the film is hard dry.

Duty statement:

  • The data in the sheet base on the information from the laboratory and practice.
  • The application may exceed the control, so we only ensure our product quality.
  • We own the right of the data sheet modification without informing.